The Technology of Polyurethane Foaming And The Performance Mechanism of Polyurethane Foaming Machine

Oct 13, 2022

Leave a message

The Technology of Polyurethane Foaming And The Performance Mechanism of Polyurethane Foaming Machine


Polyurethane foam is a polymer made of isocyanate and polyether as the main raw materials, mixed by special equipment under the action of blowing agent, catalyst, flame retardant and other additives, and foamed on site by high pressure spraying.


Polyurethane foam is divided into soft foam and hard foam: soft foam is open pore structure, hard foam is closed pore structure.


Polyurethane soft foam can be divided into two kinds of crust and non-crust, but the main function is cushioning type, manufactured products are commonly used in sofa furniture, pillows, cushions, toys, clothing and sound insulation lining these, the main characteristics are light and soft, good resilience, small relative density, high specific strength, sound absorption, breathable, heat preservation.

Polyurethane rigid foam is mainly used for adiabatic insulation, refrigeration and freezing equipment and cold storage, adiabatic panels, wall insulation, pipe insulation, insulation of storage tanks, single-component foam caulking materials, etc.

This new synthetic material with thermal insulation and waterproof function has low thermal conductivity, only 0.022~0.033W/(m*Κ), which is equivalent to half of extruded board, and is the lowest thermal conductivity among all thermal insulation materials.

Rigid polyurethane foam is mainly used in building exterior wall insulation, roofing waterproof insulation integration, cold storage insulation, pipe insulation materials, building panels, refrigerated trucks and cold storage insulation materials.

Polyurethane foam is widely used, almost penetrating into all sectors of the national economy, especially in furniture, bedding, transportation, refrigeration, construction, insulation and other sectors are very common, has become one of the indispensable materials.


Polyurethane foam machines are compressible and impact resistant, and, as cured polyurethane foam is difficult to break and does not fall off, it can be used in production with confidence. Together with its low thermal conductivity, it provides good insulation and heat retention, thus reducing the risk of accidents.

A detailed understanding of the type of machine and how it works. Most effervescent agents work by introducing gas into an aqueous solution, but the method of introduction differs. The pressure is different, even though it is the same, but the amount of bubbles produced is also different.

Second, understand the installed capacity of the machine. That is, in the total installed power, this data has a lot of information to calculate the total power consumption.

Third, understand the amount of foam produced. The foam output of polyurethane foam machine should be 0.2 higher than the actual required amount, it has some extra space, easy to operate and good performance.

When using polyurethane foam machine to fill, do not fill the whole gap, but keep out part of the empty space. After all, the foam increases and when it is completely filled, the foam will overflow and go to waste.

In addition temperature and pressure are two key variables that can be controlled reasonably to effectively improve efficiency.


Higher flexibility with proper pressure control


In the working process, once the pressure of polyurethane foaming technology is too low, it will affect the real speed of foaming. Once the pressure is too high, more specialized equipment will be needed, increasing the cost investment.

The pressure can be changed by setting the number of times the air pump is operated, thus enhancing flexibility and not affecting normal use.


Proper temperature control, fast response and stable performance


In the process of using polyurethane foam technology, the temperature should be controlled within a certain range. Once the temperature is too low, it will cause the machine's reaction speed to slow down and the curing time to lengthen, which is not conducive to the improvement of work efficiency.


To ensure more stable performance, PID control methods need to be used to improve work efficiency.


What else should we pay attention to?


When producing polyurethane materials, professional spray guns and hoses are required. The spraying equipment needs to be cleaned in advance. Don't worry that cleaning the equipment will take a lot of time, if it is not cleaned, it will seriously affect the work process.


After the spraying work is finished, it needs to be cleaned with a special cleaner. When no more material is supplied, remove the gun head and holder and place it in the solvent tank.

If you still want to continue using it, put part of the cleaner into a separate container for the next use.

If you do not want to continue using it that day, use it again the next day. The air supply to the spray system needs to be turned off to keep the inside of the unit clean and free from outside influences.

If you want to leave it for a period of time, you need to fill it up with filling fluid to avoid freezing of the spraying system.

PU tire foaming machine

Send Inquiry